Showing results: 166 - 180 of 469 items found.
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
There are CV, ACV, ACA, , CAP, Frequency, Diode Test, Continuity Test and Duty Cyclr Test function. Otherwise there are auto and manual range, relative measurement, data hold, and backlight auto off time limit mode. Test leads can be inserted on groove of back of the tester.
-
MFG-8202 -
MCH Instruments Co.,Ltd.
Features:• Low distortion, high stability• Linear and logarithmic sweep function• Sweep time and width adjustable• External Voltage Control Frequency (VCF)• Internal & external modulation (AM/FM) with modulation control• Output signal compatible with TTL/CMOS• Seven types of waveforms such as sine, square, triangle and ramp• 5W power output (ONLY for model no with “B”)• DC offset and 40bD attenuation can be applied to main output signal• Built-in frequency meter 0.1Hz~30MHz
-
MFG-8205 -
MCH Instruments Co.,Ltd.
Features:• Low distortion, high stability• Linear and logarithmic sweep function• Sweep time and width adjustable• External Voltage Control Frequency (VCF)• Internal & external modulation (AM/FM) with modulation control• Output signal compatible with TTL/CMOS• Seven types of waveforms such as sine, square, triangle and ramp• 5W power output (ONLY for model no with “B”)• DC offset and 40bD attenuation can be applied to main output signal• Built-in frequency meter 0.1Hz~30MHz
-
TFC2.5G -
Huber Signal Processing
The device provides a frequency range of up to 5 GHz and a high spectral purity, a continuous frequency or amplitude sweep, a vector modulator with 80 MHz modulation bandwidth, a fast settling time and a high signal-harmonic ratio. Due to its modular construction, options are available for retrofit. Integrated modulation modes are AM, FM, Pulse and I/Q. An integrated baseband signal generator (for e.g. QAM) is available as option. With this, baseband signals can be uploaded into the devices' memory and converted.
-
D-COAX, Inc.
D-Coax offers RF/Microwave test services for your researchprojects, as well as, production quantities tests. We have available resources and expertise in the high frequency interconnects testing that will benefit your research and products. We will work with you to make your requested tests the most accurate and reliable and we'll complete them in a timely fashion. The following parameters can be characterized or tested to specifications with our test services: Time Domain: Impedance, Impedance profile, rise time, propagation delay, skew and more. Frequency Domain: S21 - Insertion loss, S11- Return loss, S12 - Reverse Insertion loss (port 2 insertion loss), S22 - Reverse Return loss (port 2 return loss) and more.
-
ZETLAB Company
CPB analysis is used for fractional octave spectral processing of signals coming from the input channels of FFT spectrum analyzers (in real time or recorded time realization view mode), as well as for viewing various spectral characteristics of signals. CPB analysis is used for separating signals into basic constituents in the frequency area in 1/3-, 1/12-, 1/24-octave spectral bands. The software is used for noise spectral analysis within the scope of acoustic and vibrational measurements.
-
HGL Dynamics Inc
*Time & Frequency domain visualisation & analysis*Worldwide connectivity – Thin Client/Server Architecture*Interactive viewing & cursor interrogation*Mode definition & alignment*Order & mode tracking*Phase analysis with Cartesian and Polar plots*Third-octave analysis (also 1/6, 1/12, 1/24)*Rainflow and cycle-counting analysis
-
LPSU -
AWT Global
Low PIM coaxial switch matrix 5 x 6 or 1 x 4 configurationFrequency range 698-2700 MHz.SCPI commands via Ethernet (wired or wireless).Significantly reduces test time for multi frequency PIM applications.Applications: ATE systems, multi-band antenna and component testing.
-
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
PCI-9816/9846 -
ADLINK Technology Inc.
The ADLINK PCI-9816/9846 are 10MS/s, 40MS/s sampling 16-bit 4-CH digitizers designed for digitizing high frequency and wide dynamic range signals with an input frequency up to 20 MHz. The analog input range can be programmed via software to ±1 V or ±0.2 V and ±5 V or ±1 V. With a deep onboard acquisition memory up to 512 MB, the PCI-9816/PCI-9846 are not limited by the data transfer rate of the PCI bus to enable the recording of waveforms for extended periods of time.
-
ELT-400 -
Narda Safety Test Solutions
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Chongqing Blue Jay Electronic Co., Ltd.
Power Supply Voltage: Rated 220V (optional 57.7V/100V/380V) Current: Rated 5A (optional 1A) Frequency :45-65Hz 2. Load Voltage: 0.5VA / phase (rated 220V) Current: 0.5VA / phase (rated 5A) 3. Overload Current: 2 times rated continuous; 10
-
RoomScope -
Faber Acoustical, LLC
RoomScope turns your iPad, iPhone, or iPod touch into a room acoustics measurement and analysis tool. With RoomScope, you can measure a room impulse response and then calculate reverberation time, early decay time, clarity, and definition, as defined in the ISO 3382 standard. RoomScope also allows you to adjust the Schroeder decay curve integration limits with the touch of your finger and plot the calculated room parameters versus whole or 1/3-octave band center frequency.
-
MEScopeVES -
SpectraQuest, Inc.
ME’scopeVES (Visual Engineering Series) is a family of software packages and options that make it easier for you to observe, analyze, and document noise & vibration problems in machinery and structures. ME’scopeVES is used to display and analyze experimental multi-channel time or frequency domain data, acquired during the operation of a machine, or forced vibration of a structure.
-
SONASCREEN® -
SONOTEC GmbH
The handheld acoustic camera SONASCREEN generates acoustic images from both the audible and ultrasound frequency range. The device locates sound sources in real time and displays the results immediately on the screen. Furthermore, the camera provides audible feedback through industrial headphones. We make ultrasound audible and visible.